Menu List

The projector menus are organized as shown below.

DISPLAY
PICTURE
SOURCE
SYSTEM SETUP : Basic
SYSTEM SETUP : Advanced
STATUS

DISPLAY

Menu	Options (defaults in bold)
Lens Settings	Lens Shift: ‒
	Lens Shift Settings: Shift Area (Limited / Full); Home Position (No / Yes); Calibration (No / Yes)
	Lens Shift Memory: Select Memory (Memory 1~Memory 5); Load; Save; Clear; All Clear (Cancel / Reset)
	Lens Motor Lock: Lock / Unlock
	Focus 1: ‒
	Focus 2: ‒
	Zoom: ‒
Test Pattern	Off / 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16
Projector Position	Front Table / Rear Table / Rear Ceiling / Front Ceiling
Aspect Ratio	Auto / Real / 4:3 / 16:10 / 16:9 / 21:9
Digital Zoom	Proportional: On / Off
	Horizontal: 50%~100%~400%
	Vertical: 50%~100%~400%
	Digital Shift: Horizontal (0~50~100) / Vertical (0~50~100)
	Reset: Cancel / Reset
Raster Position	Horizontal: -1000~0~1000 (The upper/lower limit depends on signal or aspect ratio)
	Vertical: -600~0~600 (The upper/lower limit depends on signal or aspect ratio)
	Reset: Cancel / Reset
Blanking	Upper: 0~300pixel
	Lower: 0~300pixel
	Left: 0~500pixel
	Right: 0~300pixel
Warping & Blending	Warping & Blending Setting: Off / On / Application
	Grid Points: 2x2 / 3x3 / 5x5 / 9x9 / 17x17
	Warp Inner: On / Off
	Warp Sharpness: 0~19
	Grid Color: White / Red / Green / Blue / Magenta / Cyan
	Grid Background: Black / Transparent
	Blend Settings: Blend Width; Overlap Grid Number (4 / 6 / 8 / 10 / 12); Gamma (1.8~2.2~2.4)
	Memory: Select Memory (Memory 1~Memory 5); Load; Save; Clear; All Clear (Cancel / Reset)
	Reset: Cancel / Reset
Keystone	V: -60~0~60
Keystone	H: -60~0~60
Corner Fit	Top Left: V: 0~80 / H: 0~120
	Top Right: V: 0~80 / H: 0~120
	Bottom Left: V: 0~80 / H: 0~120
	Bottom Right: V: 0~80 / H: 0~120
Pincushion	Horizontal: 0~50~100
Pincushion	Vertical: 0~50~100

PICTURE

Menu	Options (defaults in bold)
Picture Mode	Bright / Standard[PROVIA] / Vivid[Velvia] / Cinema[ETERNA] / Multi Projection[sRGB] / High Speed / HDR
Brightness	0~50~100
Contrast	-50~0~50
TINT	-50~0~50
Saturation	-50~0~50
Gamma	1.6~2.2~3.3
Sharpness	1~8~15
Color Temperature	3200K / 4200K / 5200K / 6200K / 6500K / Default / 8200K / 9300K
Color Temperature Fine Tuning	R / G / B Gain: 0~100~200
Color Temperature Fine Tuning	R / G / B Offset: -50~0~50
7colors Tuning	R, G, B, C, M, or Y Selected for Color Hue: 0~254 Saturation: 0~254 Gain: 0~254
7colors Tuning	W Selected for Color R Gain: 0~254 G Gain: 0~254 B Gain: 0~254 White Peaking: 0~100
Dynamic Contrast	DynamicBlack: On / Off
	Speed: 1~255
	Level: 50~100% (1%/Step)
	Extreme Black: On / Off
	Light Out Timer: 0 sec~20 sec (1 sec/Step)
	Light Out Signal Level: 1~255
	Lights On Threshold: 0~127
	Reset: Cancel / Reset

INPUT

MENU	Options (defaults in bold)
SOURCE	HDMI 1 / HDMI 2 / HDBaseT
Output	HDMI 1 / HDMI 2
Color Space Conversion	Auto / RGB(0-255) / RGB(16-235) / YUV / REC709
HDMI 1 Equalizer	Auto / 1 / 2 / 3 / 4 / 5 / 6 / 7
HDMI 2 Equalizer	Auto / 1 / 2 / 3 / 4 / 5 / 6 / 7
Backup Input Settings	Auto Switch: On / Off
	Current Signal: HDMI 1 / HDMI 2 / HDBaseT (read-only)
	First Input: HDMI 1 / HDMI 2 / HDBaseT
	Second Input: HDMI 1 / HDMI 2 / HDBaseT
	Current Signal, Backup Input Status, Backup Input Change, First Input (Resolution, Vert Refresh, Horz Refresh, Color Space, HDR), Second Input (Resolution, Vert Refresh, Horz Refresh, Color Space, HDR) (read-only)
EDID Settings	HDMI 1: 2.0 / 1.4 / Custom
	HDMI 2: 2.0 / 1.4 / Custom
	HDBaseT: 2.0 / 1.4 / Custom
HDR	Auto / Off

SYSTEM SETUP : Basic

Menu	Options (defaults in bold)
Language	24 Langouage
Menu Settings	Menu Display Time: 5 sec / 10 sec / 20 sec / 30 sec / Always
	Menu Position: Center / Top Left / Top Right / Bottom Right / Bottom Left
	Reminder Message: On / Off
	Menu Transparency: 0~90
Background Color	FUJIFILM(Blue) / FUJIFILM(White) / FUJIFILM(Black) / Black / Blue / Custom
Remote Receiver	Front: On / Off
	Top: On / Off
	Rear: On / Off
	HDBaseT: On / Off
Projector ID Settings	Enable: On / Off
Projector ID Settings	Projector ID: 00~99
Panel Key Lock	On / Off
Backlight Preferences	Panel Key: On / Off / 5 sec / 10 sec / 20 sec / 30 sec
Backlight Preferences	Indicator: On / Off / Warning Errors Only
Security Settings	New / Change Password: Enter Security Code (4 digits)
Security Settings	Power On Lock: On / Off
Audio Settings	Mute: On / Off
Audio Settings	Volume: 0~50~100
4K Settings	On / Off
High Altitude Mode	On / Off
Reset Settings	Display Settings: Cancel / Reset
	Picture Settings: Cancel / Reset
	BASIC Settings: Cancel / Reset
	ADVANCED Settings: Cancel / Reset
	Initialize: Cancel / Reset

SYSTEM SETUP : Advanced

Menu	Options (defaults in bold)
Light Source Mode	Normal / Eco
Light Output	Light Output Setting: 10%~100% (1%/Step)
Light Output	Brightness Compensation: On / Off
Shutter Setting	Fade-In: Off / 0.5 sec / 1 sec / 1.5 sec / 2 sec / 2.5 sec / 3 sec / 3.5 sec / 4 sec / 4.5 sec / 5 sec (0.5 sec/Step)
	Fade-Out: Off / 0.5 sec / 1 sec / 1.5 sec / 2 sec / 2.5 sec / 3 sec / 3.5 sec / 4 sec / 4.5 sec / 5 sec (0.5 sec/Step)
	Startup: On / Off
Operation Settings	Direct Power On: On / Off
	Signal Power On: On / Off
	Auto Power Off: 0～ 180 min (5 min/Step)
	Sleep Timer: 0.0～ 16.0 hr (0.5 hr/Step)
Standby Mode	Standby / Communication
Date and Time Settings	Clock Mode: Manual / NTP
	Date: [YYYY/MM/DD]
	Time: [HH:MM]
	Daylight Saving Time: On / Off
	NTP Server IP Address: [xxx/xxx/xxx/xxx]
	Time Zone: UTC+14:00~UTC+00:00~UTC-12:00
	Update Interval: Hourly / Daily
	Apply: Yes / No
Schedule Settings	Schedule Enable: On / Off
	Daily / Sunday / Monday / Tuesday / Wednesday / Thursday / Friday / Saturday: (Off / Schedule Enable (Off / On)); Event 01~Event 16: (Time / Function / Event / Reset); Copy Events To: (Monday / Tuesday / Wednesday / Thursday / Friday / Saturday / Sunday); Reset the Day (Cancel / Reset)
	Reset: Cancel / Reset
LAN Settings	Status: Connected / Disconnected (read-only)
	MAC Address: [XX:XX:XX:XX:XX:XX] (read-only)
	Control Channel: LAN / HDBaseT
	IPv4 Settings: DHCP (On / Off); Projector IP Address ([xxx/xxx/xxx/xxx]); Subnet Mask ([xxx/xxx/xxx/xxx]); Default Gateway: ([xxx/xxx/xxx/xxx]); Primary DNS: ([xxx/xxx/xxx/xxx]); Secondary DNS: ([xxx/xxx/xxx/xxx]); Apply
	IPv6 Settings: DHCP (On / Off); Projector IP Address ([xxxx:xxxx: xxxx:xxxx:xxxx:xxxx:xxxx:xxxx]); Prefix (0~128); Default Gateway: ([xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx]); DNS: ([xxxx:xxxx:xxxx: xxxx:xxxx:xxxx:xxxx:xxxx]); Apply
LAN Control	Crestron Connected V2: On / Off
	Extron IP LINK: On / Off
	PJLink: On / Off
	AMX Device Discovery: On / Off
	Telnet: On / Off
	HTTP: On / Off
Serial Setting	9600 / 19200 / 38400 / 57600 / 115200
User Settings	Select Memory: Memory 1~Memory 5
	Load ‒
	Save ‒
	Clear ‒
	All Clear (Cancel / Reset)
Filter Settings	Filter Usage Time: XX hr (display only)
	Filter Reminder Limit: 4000 / 3500 / 3000 / 2500 / 2000 / 1500 / 1000 hours
	Reset Filter Usage Time: Cancel / Reset

STATUS

MENU	Options (defaults in bold)
Overview	Current System Status
System	Model Name, Serial Number, Standby Mode, Picture Mode, 4K Setting, Light Source Mode, Light Source Usage Total Hours, Total Projector Hours, System Temperature, Fan Info, Lens Motor Lock, and Current System Status (read-only)
System Temperature / Fan Information	DMD Board Temperature, Ambient Temperature, BLD1 Temperature, BLD2 Temperature, BLD5 Temperature, BLD6 Temperature, Fan1 Temperature, Fan2 Temperature, Fan3 Temperature, Fan4 Temperature, Fan5 Temperature, Fan6 Temperature, Fan7 Temperature, Fan8 Temperature (display only)
Communication	"Projector ID, Network Status, Control Channel, MAC Address, IPv4 Settings, IPv6 Settings (read-only)"
Signal	Current Input Signal, Resolution, Vert Refresh, Horz Refresh, Pixel Clock, and Color Space (read-only)
Backup Input Status	First Input and Second Input (read-only)
Firmware Version	Main Version, F-MCU Version, A-MCU Version, Scaler Version, LAN Version, Formatter Version, and HDBaseT Version (read-only)