Menu List

The projector menus are organized as shown below.

DISPLAY
PICTURE
SOURCE
SYSTEM SETUP : Basic
SYSTEM SETUP : Advanced
STATUS

DISPLAY

MENU	Settings (Bold indicates the default settings)
Lens Settings	Lens Shift: —
	Lens Shift Settings: Shift Area (Limited / Full), Home Position (No / Yes), Calibration (No / Yes)
	Lens Shift Memory: Select Memory (Memory 1 to Memory 5), Load, Save, Clear, All Clear (Cancel / Reset)
	Lens Motor Lock: Lock / Unlock
	Focus 1: —
	Focus 2: —
	Zoom: —
TEST PATTERN	Off / 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16
Projector Position	Front Table / Rear Table / Rear Ceiling / Front Ceiling
Aspect Ratio	Auto / Real / 4:3 / 16:10 / 16:9 / 21:9
Digital Zoom	Proportional: On / Off
	Horizontal: 50.00%～100.00%～400.00%
	Vertical: 50.00%～100.00%～400.00%
	Digital Shift: Horizontal (0.00～50.00～100.00) / Vertical (0.00～50.00～100.00)
	Reset: Cancel / Reset
Raster Position	Horizontal: -1000～0～1000 (The upper/lower limit depends on signal or aspect ratio)
	Vertical: -600 to 0 to 600 (The upper/lower limit depends on signal or aspect ratio)
	Reset: Cancel / Reset
Blanking	TOP: 0 to 600 pixels
	Bottom: 0 to 600 pixels
	left: 0 to 1000 pixels
	Right: 0 to 1000 pixels
Warping & Blending	Warping & Blending settings: Off / On / Application
	Grid Points: 2x2 / 3x3 / 5x5 / 9x9 / 17x17
	Warp Inner: On / Off
	Warp Sharpness: 0–19
	Grid Color: White / Red / Green / Blue / Magenta / Cyan
	Grid Background: Black / Transparent
	Edge Blending Setup: Blend Width, overlap grid count (4 / 6 / 8 / 10 / 12), Gamma (1.8–2.2–2.4)
	Memory: Select Memory (Memory 1–Memory 5), Load, Save, Clear, All Clear (Cancel / Reset)
	Reset: Cancel / Reset
Keystone	Vertical: -60–0–60
Keystone	Horizontal: -60–0–60
Corner Fit	Top Left: Vertical: 0–80 / Horizontal: 0 – 120
	Top Right: Vertical: 0 – 80 / Horizontal: 0 – 120
	Bottom Left: Vertical: 0 – 80 / Horizontal: 0 – 120
	Bottom Right: Vertical: 0 – 80 / Horizontal: 0 – 120
Pincushion	H: 0～50～100
Pincushion	Vertical: 0～50～100

PICTURE

MENU	Settings (Bold indicates the default settings)
Picture Mode	Bright / Standard[PROVIA] / Vivid[Velvia] / Cinema[ETERNA] / CLASSIC CHROME / CLASSIC Neg. / Multi-Projection[sRGB] / High Speed / HDR
Brightness	0 – 50 – 100
Contrast	-50 – 0 – 50
TINT	-50 – 0 – 50
Saturation	-50 – 0 – 50
Gamma	1.6 – 2.2 – 3.3
Sharpness	1 – 8 – 15
Color Temperature	3200K / 4200K / 5200K / 6200K / 6500K / Default / 8200K / 9300K
Color Temperature Fine Tuning	R / G / B gain: 0 – 100 – 200
Color Temperature Fine Tuning	R / G / B offset: -50 – 0 – 50
7colors Tuning	When colors are Red/Green/Blue/Cyan/Magenta/Yellow Hue: 0–254 Saturation: 0–254 Gain: 0–254
7colors Tuning	When color is White Red Gain: 0–254 Green Gain: 0–254 Blue Gain: 0–254 White Peaking: 0～100
Dynamic Contrast	DynamicBlack™: On / Off
	Speed: 1 to 255
	Level: 50 to 100% (1% increments)
	Extreme Black: On / Off
	Light Out Timer: 0s to 20s (1s increments)
	Light Out Signal Level: 1 to 255
	Lights on Threshold: 0 to 127
	Reset: Cancel / Reset

SOURCE

MENU	Settings (Bold indicates the default settings)
Input	HDMI 1 / HDMI 2 / HDBaseT / 12G-SDI
Output	HDMI 1 / HDMI 2
Color Space Conversion	Auto / RGB(0-255) / RGB(16-235) / YUV / REC709
HDMI 1 Equalizer	Auto / 1 / 2 / 3 / 4 / 5 / 6 / 7
HDMI 2 Equalizer	Auto / 1 / 2 / 3 / 4 / 5 / 6 / 7
Backup Input Settings	Auto Switch: On / Off
	Current Signal: HDMI 1 / HDMI 2 / HDBaseT (DISPLAY only)
	First Input: HDMI 1 / HDMI 2 / HDBaseT
	Second Input: HDMI 1 / HDMI 2 / HDBaseT
	Input Info. Current Signal, Backup Input Status, Backup Input Change, First Input (Resolution, vertical refresh, horizontal refresh, Color Space, HDR), Second Input (Resolution, vertical refresh, horizontal refresh, Color Space, HDR) (DISPLAY only)
EDID Settings	HDMI 1: 2.0 / 1.4 / Custom
	HDMI 2: 2.0 / 1.4 / Custom
	HDBaseT: 2.0 / 1.4 / Custom
HDR	Auto / Off

SYSTEM SETUP : Basic

MENU	Settings (Bold indicates the default settings)
Langouage	24 LANGUAGE
Menu Settings	Menu Display Time: 5 sec / 10 sec / 20 sec / 30 sec / Always
	Menu Location: Center / Bottom Left / Bottom Right / Top Left / Top Right
	Reminder Message: On / Off
	Menu Transparency: 0 – 90
Background Color	FUJIFILM(Blue) / FUJIFILM(White) / FUJIFILM(Black) / Black / Blue / Custom
Remote receiver	Front: On / Off
	Top: On / Off
	Rear: On / Off
	HDBaseT: On / Off
Projector ID Setting	Enable: On / Off
Projector ID Setting	Projector ID: 00 – 99
Panel Key Lock	On / Off
Backlight Preferences	Panel Key: On / Off / 5 sec / 10 sec / 20 sec / 30 sec
Backlight Preferences	Indicator: On / Off / Warning Error Only
Security Settings	new password / Change Password: Enter Security Code (4 digits)
Security Settings	Power On Lock: On / Off
4K Settings	On / Off
High Altitude Mode	On / Off
Reset Settings	Display Settings: Cancel / Reset
	Picture Settings: Cancel / Reset
	BASIC Settings: Cancel / Reset
	ADVANCED Settings: Cancel / Reset
	Initialization: Cancel / Reset

SYSTEM SETUP : Advanced

MENU	Settings (Bold indicates the default settings)
Light Source Mode	Normal / Eco
Light Output Settings	Light Output Setting: 10%～100% (1%/step)
Light Output Settings	Brightness Compensation: On / Off
Shutter Setting	Fade-In: Off / 0.5 s / 1 s / 1.5 s / 2 s / 2.5 s / 3 s / 3.5 s / 4 s / 4.5 s / 5 sec
	Fade-Out: Off / 0.5 s / 1 s / 1.5 s / 2 s / 2.5 s / 3 s / 3.5 s / 4 s / 4.5 s / 5 sec
	Startup: On / Off
Operation Settings	Direct Power On: On / Off
	Signal Power On: On / Off
	Auto Power Off: 0 to 180 m (5 m / step)
	Sleep Timer: 0.0 to 16.0 Hour (0.5 Hour / step)
Standby Mode	Standby / Communication
Date and Time Settings	Clock Mode: Manual / NTP
	Date: [YYYY/MM/DD]
	Time: [HH:MM]
	Daylight Saving Time: On / Off
	NTP Server IP Address: [xxx/xxx/xxx/xxx]
	Time Zone: UTC+14:00 to UTC+00:00 to UTC-12:00
	Update Interval: Hourly / Daily
	Apply: Yes / No
Schedule Settings	Schedule Enable: On / Off
	Daily / Sunday / Monday / Tuesday / Wednesday / Thursday / Friday / Saturday: (Off / Schedule Enable (Off / On)), Event 01 to Event 16: (Time / Function / Event / Reset), Copy Events To: (Monday / Tuesday / Wednesday / Thursday / Friday / Saturday / Sunday), Reset the Day (Cancel / Reset)
	Reset: Cancel / Reset
LAN Settings	Status: Connection / Disconnected (DISPLAY only)
	MAC Address: [XX:XX:XX:XX:XX:XX] (DISPLAY only)
	Control Channel: LAN / HDBaseT
	IPv4 Settings: DHCP (On / Off), Projector IP Address ([xxx/xxx/xxx/xxx]), Subnet Mask ([xxx/xxx/xxx/xxx]), Default Gateway: ([xxx/xxx/xxx/xxx]), Primary DNS: ([xxx/xxx/xxx/xxx]), Secondary DNS: ([xxx/xxx/xxx/xxx]), Apply
	IPv6 Settings: DHCP (On / Off), Projector IP Address ([xxxx:xxxx: xxxx:xxxx:xxxx:xxxx:xxxx:xxxx]), Prefix (0–128), Default Gateway: ([xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx]), DNS: ([xxxx:xxxx:xxxx: xxxx:xxxx:xxxx:xxxx:xxxx]), Apply
LAN Control	Crestron Connected V2: On / Off
	Extron IP LINK: On / Off
	PJLink: On / Off
	AMX Device Discovery: On / Off
	Telnet: On / Off
	HTTP: On / Off
Serial Setting	9600 / 19200 / 38400 / 57600 / 115200
User Settings	Select Memory: Memory 1–Memory 5
	Load -
	Save ‒
	Clear ‒
	All Clear (Cancel / Reset)
filter settings	filter usage time: XXhr (DISPLAY only)
	filter usage reminder limit: 4000/3500/3000/2500/2000/1500/1000 Hour
	reset filter usage hours: Cancel / Reset

STATUS

MENU	Settings (Bold indicates the default settings)
Summary	Current System Status
System	Current System Status (DISPLAY only), Model Name / lens model name, Serial Number, STANDBY MODE, picture mode, 4K Setting, Light Source Mode, Light Source Usage Total Hours, Total Projector Hours, Lens Motor Lock, filter installation, filter usage time
System temperature/fan information	System temperature, DMD board temperature, ambient temperature, phosphor wheel temperature, BLD1 temperature, BLD2 temperature, BLD3 temperature, BLD4 temperature, BLD5 temperature, BLD6 temperature, fan 1 temperature, fan 2 temperature, fan 3 temperature, fan 4 temperature, fan 5 temperature, fan 8 temperature, fan 9 temperature, fan 10 temperature, fan 11 temperature (DISPLAY only)
Communication	"Projector ID, Network Status, Control Channel, MAC Address, IPv4 Settings, IPv6 Settings (read-only)"
Signal	Current Input Signal, Resolution, vertical refresh, horizontal refresh, pixel clock, Color Space (DISPLAY only)
Backup Input Status	Auto Switch: On/Off, first input signal, second input signal (DISPLAY only)
firmware version	"Main Version, F-MCU Version, A-MCU Version, Scaler Version, LAN Version, Formatter Version, and HDBaseT Version (read-only)"