Enter a search term and click .

Parts of the Projector: Names and Functions

Item Name
1 Lens
2 Indicator lamps
3 Control panel
4 Remote receiver
5 Interface (connector) panel
6 Speaker
7 Security slot *
Item Name
8 Adjustable feet
9 Security lock
10 Intake vents
11 Exhaust vent
12 Power connector
13 Main power

* Compatible with Kensington MicroSaver security system locks.

Control panel

Basic operations are performed using the control panel. The names and functions of the buttons on the control panel are given below.

Item Button Function
1 (power)

Turn the projector on or switch it to standby.

The projector automatically switches to standby about three seconds after the lens is returned to the storage position.

2 LENS Adjust lens focus, shift, and zoom.
3 Selector Navigate the menus.
4 ENTER Select the highlighted menu item.
5 MENU Display the menus used to adjust projector settings.
6 SHUTTER Temporarily suspend projection and mute audio. Press again to resume.
7 BACK Return to the previous menu.
8 HDMI1 Select HDMI 1 (FP-Z8000).
INPUT Select an input source (FP-Z6000).
9 HDMI2 Select HDMI 2 (FP-Z8000).
HDMI1 Select HDMI 1 (FP-Z6000).
10 DisplayPort Select DisplayPort.
11 HDBaseT Select HDBaseT.
12 SDI Select SDI.

The Arm and Head Latches

The lens can be rotated and is equipped latches for the arm and projector head. Rotate the lens as described below. Be sure to latch the lens while projector is in use.


  • Some portions of the projected image may not be visible depending on lens shift and the orientation of the lens.
  • When rotated, the lens automatically returns to the previous shift position, causing the picture move. Do not rotate the lens while lens shift is in progress (i.e., while the image is moving).
  • When rotating the lens, keep it supported and rotate it slowly.
  • Pay attention to your surroundings when rotating the lens. Light from the product projected into the eyes could cause visual impairment.

Rotating the Arm

When the arm latch is disengaged by pressing the arm latch release, the arm can be rotated 90°. Lift the latch release to latch the arm once more.



Rotating the Projector Head

When the head latch is disengaged by sliding the head latch release to the FREE position, the projector head can be rotated 360° in 90° increments.

AFREE position

BLOCK position

The lens can be rotated when the head latch release is in the FREE position and latches when the release is in the LOCK position.


Do not return the arm to the storage position with the lens facing down. Failure to observe this precaution could scratch or break the lens.


Observe the following precautions to prevent the lens being scratched or broken during transport and storage.

  • Return the lens to the home lens shift position. (: Hold the SHIFT button for 3 seconds.)
  • Be sure to return the lens to the storage position.
  • Attach the two protective covers (one large and one small) to the lens for transport.

    Large cover

    Small cover


Connect devices to the connectors using the appropriate cables.

Connector Description
Video IN 1 HDMI 1 IN HDMI 2.0 (compatible with HDCP 2.2, accepts 3840 × 2160 60P input)
2 DisplayPort IN Display Port1.2 (compatible HDCP 1.3, accepts 3840 × 2160 60P input)
3 SDI IN BNC (3G/HD/SD SDI input)
4 HDBaseT IN RJ-45 for video/audio/connection control (accepts 3840 × 2160 60P input)
Control IN/OUT 5 LAN RJ-45 for network connection (10Base-T/100Base-TX)
6 HDBaseT IN RJ-45 for projector connection control
7 RS‑232C IN D-Sub 9 pin for projector connection control
Audio IN/OUT 8 AUDIO IN 3.5 mm stereo mini jack
9 AUDIO OUT 3.5 mm stereo mini jack
Other 10 USB 1 Type A for maintenance, DC 5V 1.5A (Max)
Warping/edge blending function *1
(FP-Z8000 only)
11 HDMI 2 IN *2 HDMI 1.4 (compatible with HDCP 1.4, audio input not supported)
12 USB 2 Type A for warping/edge blending function

For information on connecting cables, see aConnections”.

Input selection is made via software. At default settings, the input signal resolution is fixed at 1920 × 1200. Input at resolutions other than the selected value may produce unexpected results.


  • Before connecting cables, switch the projector to standby and confirm that the peripheral is either off or in standby mode. After connecting the cable to both devices, turn the projector on first and then turn on the peripheral.
  • Some devices require an adapter and/or a dedicated cable.

Indicator Lamps

Projector status is shown by whether the indicator (ON/STANDBY, TEMP, and STATUS) lamps are on, flashing, or off.

The statuses shown by the condition of the indicator lamps are listed below.

On (red) Off Off Projector in standby mode.
On (green) Off Off Projector on.
On (green) Flashing (red) Off Projector temperature elevated.
Flashing (red) Off Off Network standby.
On (green) or flashing (green) or off On (red) or off On (red) or flashing (red) Problem with cooling fan.